Expansion and differentiation of ex vivo cultured erythroblasts in scalable stirred bioreactors.

Transfusion of donor-derived red blood cells (RBCs) is the most common form of cell therapy. Production of transfusion-ready cultured RBCs (cRBCs) is a promising replacement for the current, fully donor-dependent therapy. A single transfusion unit, however, contains 2 × 1012 RBC, which requires large scale production. Here, we report on the scale-up of cRBC production from static cultures of erythroblasts to 3 L stirred tank bioreactors, and identify the effect of operating conditions on the efficiency of the process. Oxygen requirement of proliferating erythroblasts (0.55-2.01 pg/cell/h) required sparging of air to maintain the dissolved oxygen concentration at the tested setpoint (2.88 mg O2 /L). Erythroblasts could be cultured at dissolved oxygen concentrations as low as 0.7 O2 mg/ml without negative impact on proliferation, viability or differentiation dynamics. Stirring speeds of up to 600 rpm supported erythroblast proliferation, while 1800 rpm led to a transient halt in growth and accelerated differentiation followed by a recovery after 5 days of culture. Erythroblasts differentiated in bioreactors, with final enucleation levels and hemoglobin content similar to parallel cultures under static conditions.

A possible influence of extracellular polysaccharides on the analysis of intracellular metabolites from Trichoderma harzianum grown under carbon-limited conditions.

Intracellular metabolites were evaluated during the continuous growth of Trichoderma harzianum P49P11 under carbon-limited conditions. Four different conditions in duplicate were investigated (10 and 20 g/L of glucose, 5.26/5.26 g/L of fructose/glucose and 10 g/L of sucrose in the feed). Differences in the values of some specific concentrations of intracellular metabolites were observed at steady-state for the duplicates. The presence of extracellular polysaccharide was confirmed in the supernatant of all conditions based on FT-IR and proton NMR. Fragments of polysaccharides from the cell wall could be released due to the shear stress and since the cells can consume them under carbon-limited conditions, this could create an unpredictable carbon flow rate into the cells. According to the values of the metabolite concentrations, it was considered that the consumption of those fragments was interfering with the analysis.

Continuous production of enzymes under carbon-limited conditions by Trichoderma harzianum P49P11.

Carbon-limited chemostat cultures were performed using different carbon sources (glucose, 10 and 20 g/L; sucrose, 10 g/L; fructose/glucose, 5.26/5.26 g/L; carboxymethyl cellulose, 10 g/L; and carboxymethyl cellulose/glucose, 5/5 g/L) to verify the capability of the wild type strain Trichoderma harzianum to produce extracellular enzymes. All chemostat cultures were carried out at a fixed dilution rate of 0.05 h-1. Experiments using glucose, fructose/glucose and sucrose were performed in duplicate. Glucose condition was found to induce the production of enzymes that can catalyse the hydrolysis of p-nitrophenyl-ß-d-glucopyranoside (PNPGase). A concentration of 20 g/L of glucose in the feed provided the highest productivity (1048 ± 16 U/mol h). Extracellular polysaccharides were considered the source of inducers. Based on the obtained results, a new PNPGase production process was developed using mainly glucose. This process raises interesting possibilities of synthesizing the inducer substrate and the induced enzymes in a single step using an easily assimilated carbon source under carbon-limited conditions.

Bioprocess intensification: Cases that (don't) work.

Development of affordable and low carbon biobased manufacturing depends critically on strategies that reduce cost and emission profiles. This paper indicates that efforts around the reduction of capital costs by intensification of process equipment need to be carefully weighed against the inherently fast increasing financial and climate costs of driving forces used for the intensification. The fundamental relation between capital expenditures (CAPEX) and operational expenditures (OPEX) of intensified and non-intensified biobased processes and their financial and climatic impacts are emphasized and provisionally explored for a few industrial processes. General learnings flag the importance in particular of OPEX minimisation for sustainable bio-economic development.

Enzymatic Hydrolysis of Sugarcane Bagasse in Aqueous Two-Phase Systems (ATPS): Exploration and Conceptual Process Design.

The enzymatic conversion of lignocellulosic material to sugars can provide a carbon source for the production of energy (fuels) and a wide range of renewable products. However, the efficiency of this conversion is impaired due to product (sugar) inhibition. Even though several studies investigate how to overcome this challenge, concepts on the process to conduct the hydrolysis are still scarce in literature. Aqueous two-phase systems (ATPS) can be applied to design an extractive reaction due to their capacity to partition solutes to different phases in such a system. This work presents strategies on how to conduct extractive enzymatic hydrolysis in ATPS and how to explore the experimental results in order to design a feasible process. While only a limited number of ATPS was explored, the methods and strategies described could easily be applied to any further ATPS to be explored. We studied two promising ATPS as a subset of a previously high throughput screened large set of ATPS, providing two configurations of processes having the reaction in either the top phase or in the bottom phase. Enzymatic hydrolysis in these ATPS was performed to evaluate the partitioning of the substrate and the influence of solute partitioning on conversion. Because ATPS are able to partition inhibitors (sugar) between the phases, the conversion rate can be maintained. However, phase forming components should be selected to preserve the enzymatic activity. The experimental results presented here contribute to a feasible ATPS-based conceptual process design for the enzymatic conversion of lignocellulosic material.

Analysis of the proteins secreted by Trichoderma harzianum P49P11 under carbon-limited conditions.

The wild type strain Trichoderma harzianum was able to synthesize enzymes that can catalyse the hydrolysis of p-nitrophenyl-ß-D-glucopyranoside (PNPGase) in glucose-limited chemostat cultures. Fructose/glucose and sucrose conditions provided low levels of PNPGase activity. To investigate whether under these conditions other enzymes were produced, a shotgun proteomics analysis of their supernatants was performed. The analysis has indicated that the different carbon sources used influenced the amounts of proteins secreted including 1,3-beta-glucanosyltransferase, alpha-1,2-mannosidase, alpha-galactosidase and glucan 1,3-beta-glucosidase. The analysis has also suggested the presence of beta-glucosidase, which could also be represented by PNPGase activity. Intracellular metabolites were quantified during PNPGase production for the condition using 20 g/L of glucose in the feed and differences were observed, indicating that intracellular glucose could be inhibiting PNPGase production. SIGNIFICANCE: This work shows that sugars such as glucose, fructose/glucose and sucrose can be used as substrates for the continuous synthesis of different enzymes under carbon-limited conditions by Trichoderma harzianum. As far as we know, this is the first work about the continuous synthesis of enzymes under carbon-limited conditions suggesting that different easily assimilated carbon sources can be used to generate different enzymatic cocktails. Each enzyme or uncharacterized protein suggested by shotgun proteomics has the potential to become a promising product for biotechnological applications.

Integrated Vacuum Stripping and Adsorption for the Efficient Recovery of (Biobased) 2-Butanol.

Biobased 2-butanol offers high potential as biofuel, but its toxicity toward microbial hosts calls for efficient techniques to alleviate product inhibition in fermentation processes. Aiming at the selective recovery of 2-butanol, the feasibility of a process combining in situ vacuum stripping followed by vapor adsorption has been assessed using mimicked fermentation media. The experimental vacuum stripping of model solutions and corn stover hydrolysate closely aligned with mass transfer model predictions. However, the presence of lignocellulosic impurities affected 2-butanol recovery yields resulting from vapor condensation, which decreased from 96 wt % in model solutions to 40 wt % using hydrolysate. For the selective recovery of 2-butanol from a vapor mixture enriched in water and carbon dioxide, silicalite materials were the most efficient, particularly at low alcohol partial pressures. Integrating in situ vacuum stripping with vapor adsorption using HiSiv3000 proved useful to effectively concentrate 2-butanol above its azeotropic composition (>68 wt %), facilitating further product purification.

A robotic platform to screen aqueous two-phase systems for overcoming inhibition in enzymatic reactions.

Aqueous two-phase systems (ATPS) can be applied to enzymatic reactions that are affected by product inhibition. In the biorefinery context, sugars inhibit the cellulolytic enzymes in charge of converting the biomass. Here, we present a strategy to select an ATPS (formed by polymer and salt) that can separate sugar and enzymes. This automated and miniaturized method is able to determine phase diagrams and partition coefficients of solutes in these. Tailored approaches to quantify the solutes are presented, taking into account the limitations of techniques that can be applied with ATPS due to the interference of phase forming components with the analytics. The developed high-throughput (HT) platform identifies suitable phase forming components and the tie line of operation. This fast methodology proposes to screen up to six different polymer-salt systems in eight days and supplies the results to understand the influence of sugar and protein concentrations on their partition coefficients.

Perspectives for the microbial production of methyl propionate integrated with product recovery.

A new approach was studied for bio-based production of methyl propionate, a precursor of methyl methacrylate. Recombinant E. coli cells were used to perform a cascade reaction in which 2-butanol is reduced to butanone using alcohol dehydrogenase, and butanone is oxidized to methyl propionate and ethyl acetate using a Baeyer-Villiger monooxygenase (BVMO). Product was removed by in situ stripping. The conversion was in line with a model comprising product formation and stripping kinetics. The maximum conversion rates were 1.14 g-butanone/(L h), 0.11 g-ethyl acetate/(L h), and 0.09 g-methyl propionate/(L h). The enzyme regioselectivity towards methyl propionate was 43% of total ester. Starting from biomass-based production of 2-butanol, full-scale ester production with conventional product purification was calculated to be competitive with petrochemical production if the monooxygenase activity and regioselectivity are enhanced, and the costs of bio-based 2-butanol are minimized.

Integration of Gas Enhanced Oil Recovery in Multiphase Fermentations for the Microbial Production of Fuels and Chemicals.

In multiphase fermentations where the product forms a second liquid phase or where solvents are added for product extraction, turbulent conditions disperse the oil phase as droplets. Surface-active components (SACs) present in the fermentation broth can stabilize the product droplets thus forming an emulsion. Breaking this emulsion increases process complexity and consequently the production cost. In previous works, it has been proposed to promote demulsification of oil/supernatant emulsions in an off-line batch bubble column operating at low gas flow rate. The aim of this study is to test the performance of this recovery method integrated to a fermentation, allowing for continuous removal of the oil phase. A 500 mL bubble column is successfully integrated with a 2 L reactor during 24 h without affecting cell growth or cell viability. However, higher levels of surfactants and emulsion stability are measured in the integrated system compared to a base case, reducing its capacity for oil recovery. This is related to release of SACs due to cellular stress when circulating through the recovery column. Therefore, it is concluded that the gas bubble-induced oil recovery method allows for oil separation and cell recycling without compromising fermentation performance; however, tuning of the column parameters considering increased levels of SACs due to cellular stress is required for improving oil recovery.

Prospects and challenges for the recovery of 2-butanol produced by vacuum fermentation - a techno-economic analysis.

The conceptual design of a bio-based process for 2-butanol production is presented for the first time. Considering a hypothetical efficient producing strain, a vacuum fermentation is proposed to alleviate product toxicity, but the main challenge is the energy-efficient product recovery from the vapor. Three downstream scenarios were examined for this purpose: 1) multi-stage vapor recompression; 2) temperature swing adsorption; and 3) vapor absorption. The processes were simulated using Aspen Plus, considering a production capacity of 101 kton/yr. Process optimization was performed targeting the minimum selling price of 2-butanol. The feasibility of the different configurations was analyzed based on the global energy requirements and capital expenditure. The use of integrated adsorption and absorption minimized the energy duty required for azeotrope purification, which represents 11% of the total operational expenditure in Scenario 1. The minimum selling price of 2-butanol as commodity chemical was estimated as 1.05 $/kg, 1.21 $/kg, and 1.03 $/kg regarding the fermentation integrated with downstream scenarios 1), 2), and 3), respectively. Significant savings in 2-butanol production could be achieved in the suggested integrated configurations if more efficient microbial strains were engineered, and more selective adsorption and absorption materials were found for product recovery.

Esters production via carboxylates from anaerobic paper mill wastewater treatment.

This paper describes a new option for integrated recovery and esterification of carboxylates produced by anaerobic digestion at a pH above the pKa. The carboxylates (acetate, propionate, butyrate, valerate and lactate) are recovered using a strong anion exchange resin in the bicarbonate form, and the resin is regenerated using a CO2-expanded alcohol technique, which allows for low chemicals consumption and direct esterification. Paper mill wastewater was used to study the effect of pH and the presence of other inorganic anions and cations on the adsorption and desorption with CO2-expanded methanol. Calcium, which is present in paper mill wastewater, can cause precipitation problems, especially at high pH. Esters yields ranged from 1.08±0.04mol methyl acetate/mol of acetatein to 0.57±0.02mol methyl valerate/mol of valeratein.

Optimization of biopharmaceutical downstream processes supported by mechanistic models and artificial neural networks.

Downstream process development is a major area of importance within the field of bioengineering. During the design of such a downstream process, important decisions have to be made regarding the type of unit operations as well as their sequence and their operating conditions. Current computational approaches addressing these issues either show a high level of simplification or struggle with computational speed. Therefore, this article presents a new approach that combines detailed mechanistic models and speed-enhancing artificial neural networks. This approach was able to simultaneously optimize a process with three different chromatographic columns toward yield with a minimum purity of 99.9%. The addition of artificial neural networks greatly accelerated this optimization. Due to high computational speed, the approach is easily extendable to include more unit operations. Therefore, it can be of great help in the acceleration of downstream process development. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:696-707, 2017.

Selective adsorption of flavor-active components on hydrophobic resins.

This work aims to propose an optimum resin that can be used in industrial adsorption process for tuning flavor-active components or removal of ethanol for producing an alcohol-free beer. A procedure is reported for selective adsorption of volatile aroma components from water/ethanol mixtures on synthetic hydrophobic resins. High throughput 96-well microtiter-plates batch uptake experimentation is applied for screening resins for adsorption of esters (i.e. isoamyl acetate, and ethyl acetate), higher alcohols (i.e. isoamyl alcohol and isobutyl alcohol), a diketone (diacetyl) and ethanol. The miniaturized batch uptake method is adapted for adsorption of volatile components, and validated with column breakthrough analysis. The results of single-component adsorption tests on Sepabeads SP20-SS are expressed in single-component Langmuir, Freundlich, and Sips isotherm models and multi-component versions of Langmuir and Sips models are applied for expressing multi-component adsorption results obtained on several tested resins. The adsorption parameters are regressed and the selectivity over ethanol is calculated for each tested component and tested resin. Resin scores for four different scenarios of selective adsorption of esters, higher alcohols, diacetyl, and ethanol are obtained. The optimal resin for adsorption of esters is Sepabeads SP20-SS with resin score of 87% and for selective removal of higher alcohols, XAD16N, and XAD4 from Amberlite resin series are proposed with scores of 80 and 74% respectively. For adsorption of diacetyl, XAD16N and XAD4 resins with score of 86% are the optimum choice and Sepabeads SP2MGS and XAD761 resins showed the highest affinity towards ethanol.

3D-liquid chromatography as a complex mixture characterization tool for knowledge-based downstream process development.

Knowledge-based development of chromatographic separation processes requires efficient techniques to determine the physicochemical properties of the product and the impurities to be removed. These characterization techniques are usually divided into approaches that determine molecular properties, such as charge, hydrophobicity and size, or molecular interactions with auxiliary materials, commonly in the form of adsorption isotherms. In this study we demonstrate the application of a three-dimensional liquid chromatography approach to a clarified cell homogenate containing a therapeutic enzyme. Each separation dimension determines a molecular property relevant to the chromatographic behavior of each component. Matching of the peaks across the different separation dimensions and against a high-resolution reference chromatogram allows to assign the determined parameters to pseudo-components, allowing to determine the most promising technique for the removal of each impurity. More detailed process design using mechanistic models requires isotherm parameters. For this purpose, the second dimension consists of multiple linear gradient separations on columns in a high-throughput screening compatible format, that allow regression of isotherm parameters with an average standard error of 8%. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:1283-1291, 2016.

Prediction of protein retention times in hydrophobic interaction chromatography by robust statistical characterization of their atomic-level surface properties.

The correlation between the dimensionless retention times (DRT) of proteins in hydrophobic interaction chromatography (HIC) and their surface properties were investigated. A ternary atomic-level hydrophobicity scale was used to calculate the distribution of local average hydrophobicity across the proteins surfaces. These distributions were characterized by robust descriptive statistics to reduce their sensitivity to small changes in the three-dimensional structure. The applicability of these statistics for the prediction of protein retention behaviour was looked into. A linear combination of robust statistics describing the central tendency, heterogeneity and frequency of highly hydrophobic clusters was found to have a good predictive capability (R2 = 0.78), when combined a factor to account for protein size differences. The achieved error of prediction was 35% lower than for a similar model based on a description of the protein surface on an amino acid level. This indicates that a robust and mathematically simple model based on an atomic description of the protein surface can be used for the prediction of the retention behaviour of conformationally stable globular proteins with a well determined 3D structure in HIC. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:372-381, 2016.

Fermentation broth components influence droplet coalescence and hinder advanced biofuel recovery during fermentation.

Developments in synthetic biology enabled the microbial production of long chain hydrocarbons, which can be used as advanced biofuels in aviation or transportation. Currently, these fuels are not economically competitive due to their production costs. The current process offers room for improvement: by utilizing lignocellulosic feedstock, increasing microbial yields, and using cheaper process technology. Gravity separation is an example of the latter, for which droplet growth by coalescence is crucial. The aim of this study was to study the effect of fermentation broth components on droplet coalescence. Droplet coalescence was measured using two setups: a microfluidic chip and regular laboratory scale stirred vessel (2 L). Some fermentation broth components had a large impact on droplet coalescence. Especially components present in hydrolysed cellulosic biomass and mannoproteins from the yeast cell wall retard coalescence. To achieve a technically feasible gravity separation that can be integrated with the fermentation, the negative effects of these components on coalescence should be minimized. This could be achieved by redesign of the fermentation medium or adjusting the fermentation conditions, aiming to minimize the release of surface active components by the microorganisms. This way, another step can be made towards economically feasible advanced biofuel production.

Fourier transform assisted deconvolution of skewed peaks in complex multi-dimensional chromatograms.

Lower order peak moments of individual peaks in heavily fused peak clusters can be determined by fitting peak models to the experimental data. The success of such an approach depends on two main aspects: the generation of meaningful initial estimates on the number and position of the peaks, and the choice of a suitable peak model. For the detection of meaningful peaks in multi-dimensional chromatograms, a fast data scanning algorithm was combined with prior resolution enhancement through the reduction of column and system broadening effects with the help of two-dimensional fast Fourier transforms. To capture the shape of skewed peaks in multi-dimensional chromatograms a formalism for the accurate calculation of exponentially modified Gaussian peaks, one of the most popular models for skewed peaks, was extended for direct fitting of two-dimensional data. The method is demonstrated to successfully identify and deconvolute peaks hidden in strongly fused peak clusters. Incorporation of automatic analysis and reporting of the statistics of the fitted peak parameters and calculated properties allows to easily identify in which regions of the chromatograms additional resolution is required for robust quantification.

Feasibility study of an alkaline-based chemical treatment for the purification of polyhydroxybutyrate produced by a mixed enriched culture.

This study focused on investigating the feasibility of purifying polyhydroxybutyrate (PHB) from mixed culture biomass by alkaline-based chemical treatment. The PHB-containing biomass was enriched on acetate under non-sterile conditions. Alkaline treatment (0.2 M NaOH) together with surfactant SDS (0.2 w/v% SDS) could reach 99% purity, with more than 90% recovery. The lost PHB could be mostly attributed to PHB hydrolysis during the alkaline treatment. PHB hydrolysis could be moderated by increasing the crystallinity of the PHB granules, for example, by biomass pretreatment (e.g. freezing or lyophilization) or by effective cell lysis (e.g. adjusting alkali concentration). The suitability of the purified PHB by alkaline treatment for polymer applications was evaluated by molecular weight and thermal stability. A solvent based purification method was also performed for comparison purposes. As result, PHB produced by mixed enriched cultures was found suitable for thermoplastic applications when purified by the solvent method. While the alkaline method resulted in purity, recovery yield and molecular weight comparable to values reported in literature for PHB produced by pure cultures, it was found unsuitable for thermoplastic applications. Given the potential low cost and favorable environmental impact of this method, it is expected that PHB purified by alkaline method may be suitable for other non-thermal polymer applications, and as a platform chemical.